Sermorelin Dosage Chart: Reconstitution and Syringe Units
A sermorelin dosage chart answers one question: once the vial is reconstituted, how many units on an insulin syringe correspond to a given amount. That is arithmetic, and it is identical for every peptide, so the chart below applies to Sermorelin exactly as it does to any other compound. It is not a protocol and it recommends no amount: what amount is appropriate for a person, if any, is a question for a qualified healthcare professional.
Reconstitution chart, using 2 mL of bacteriostatic water:
| Vial strength | Concentration | 1 syringe unit delivers | Units for 250 mcg | Units for 500 mcg | Units for 1 mg |
|---|---|---|---|---|---|
| 2 mg | 1 mg/mL | 10 mcg | 25 | 50 | 100 |
| 5 mg | 2.5 mg/mL | 25 mcg | 10 | 20 | 40 |
| 10 mg | 5 mg/mL | 50 mcg | 5 | 10 | 20 |
| 20 mg | 10 mg/mL | 100 mcg | 2.5 | 5 | 10 |
| 50 mg | 25 mg/mL | 250 mcg | 1 | 2 | 4 |
An insulin syringe unit is 0.01 mL, so one unit always delivers the concentration multiplied by 10 in micrograms. That single fact is what the whole chart is built on.
Using a different volume of water: the chart scales linearly. With 1 mL of bacteriostatic water the concentration doubles, so use half the units shown. With 3 mL it drops by a third, so use 1.5 times the units shown. The calculator at the top of this page does this for any combination, including volumes that are not round numbers.
Reference values only. Verify every calculation against your own vial before any handling, and remember that a reconstituted vial must be stored refrigerated.
What Published Studies Say About the Sermorelin Dose
Sermorelin is a 29 amino acid analogue of human growth hormone-releasing hormone (GHRH). It is described as the shortest synthetic peptide with the full biological activity of GHRH, and it stimulates growth hormone secretion from the anterior pituitary.
The doses in the published clinical literature are based on body weight and come from pediatric use: a single intravenous dose of 1 mcg per kg as a diagnostic test of growth hormone deficiency, and 30 mcg per kg by subcutaneous injection once daily at bedtime in prepubertal children with idiopathic growth hormone deficiency, on what the review calls limited data. The most commonly reported adverse events were transient facial flushing and pain at the injection site (Prakash and Goa, 1999, PMID 18031173).
We found no sermorelin product label on DailyMed (checked in November 2026). The figures that circulate for adults, roughly 200 to 500 mcg per day, come from clinic and community practice and not from a current label. The presets of this calculator sit in that band so that the arithmetic is easy to check. They are not a recommendation.
Sermorelin doses for adults are not clinically validated for self-administration. This tool is educational only and is not medical advice or a dosing recommendation. Any use belongs under the supervision of a qualified healthcare professional.
How to Use This Peptide Calculator
Enter Peptide Amount
Input the total milligrams (mg) in your peptide vial. Common sizes: 2mg, 5mg, 10mg.
Add Water Volume
Enter how much bacteriostatic water (BAC water) you'll add. More water = easier to measure small doses.
Set Your Dose
Enter your desired dose in micrograms (mcg). The calculator shows exact syringe units to draw.
To understand the mechanism, the clinical studies and the side effects of this peptide, read our complete Sermorelin guide.
Need More Than a Calculator?
Track your protocol with Peptide Lab
The calculator is just the start. The app is free and includes:
- Interactive body map 14 sites, smart rotation
- Weight & effects tracking correlate your results with your protocol
- Half-life curves optimize your timing
- 10 training chapters master reconstitution
The Math Behind Peptide Reconstitution
Concentration formula:
Concentration (mg/mL) = Peptide (mg) ÷ Water (mL)Units to draw:
Units = [Dose (mcg) ÷ 1000] ÷ Concentration × 100Example: Sermorelin 250mcg dose
- 5mg vial + 2mL BAC water = 2.5 mg/mL
- 250mcg = 0.25mg
- 0.25mg ÷ 2.5 mg/mL = 0.10mL
- 0.10mL × 100 = 10 units on insulin syringe
Understanding Insulin Syringe Units
10 units = 0.10 mL
Quick Reference
- 100 units = 1 mL (full syringe)
- 50 units = 0.5 mL (half syringe)
- 10 units = 0.1 mL (1/10th syringe)
- 1 unit = 0.01 mL
Standard insulin syringes are U-100, meaning 100 units per mL. This calculator uses this standard.
Popular Peptide Dosage Charts
| Peptide | Common Vial | Typical Dose | BAC Water | Units to Draw |
|---|---|---|---|---|
| BPC-157 | 5mg | 250mcg | 2mL | 10 units |
| TB-500 | 5mg | 2.5mg (loading) | 2mL | 100 units |
| Semaglutide | 5mg | 250mcg | 2mL | 10 units |
| CJC-1295 | 2mg | 100mcg | 2mL | 10 units |
| Ipamorelin | 5mg | 200mcg | 2mL | 8 units |
| GHK-Cu | 50mg | 1mg | 5mL | 10 units |
| KPV | 5mg | 200mcg | 2mL | 8 units |
| Epithalon | 10mg | 5mg | 2mL | 100 units |
These are common research doses. Always verify with your protocol. This calculator is for educational purposes only.
Printable reconstitution chart, free
Get the reference chart by email (concentrations, µg per 10 units, formulas, storage) to keep next to your prep space.
We will never share your email.
Prices and stock are set by each vendor and can change. Always confirm third-party testing on the vendor site.